Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I have read the documents regarding the powering up the board form external supply and switch position
i need simple answer how power the board completely means...
Hello Nordic team,
I am trying to use external flash on nRF52840dk using Qspi.
Above is my overlay file.
Above is my pm_static file.
I am using custom board where...
I am trying to send a variety of AT commands to my module and it looks like I am missing something or the documentation is not up to date for some of these:
If I try to...
Good morning,
After updating the VSCode extension "nRF Connect SDK" to version v2024.12.55 , I encountered an issue where the "Build" and "Action" menus do not update after...
The datasheet, page 78, says "Supervisor HW to manage power on reset, brownout, and power fail".
We are powering from a solar cell, so the power supply voltage ramp will...
HI i am using nordic nrf52840 dk(pca10056) . i am using ble_app_uart example code for my development. i have connected usb in j2 but when i keep my power switch in usb adv...
Hi! I want to write some software utilizing OpenThread and CoAP. I've seen samples of coap server and coap client in NCS. However, I want to ask whether it's possible or not...
Hi,
I am currently investigating the possibility of using Nordic nRF52840 as the PAwR advertiser and the other device (from a different vendor) as the PAwR scanner. I don...
nRF 52832 + NCS 2.6.1
We are successfully setting the advertising Tx power in discrete steps {-40, -20, -16, -12, -8, -4, 0, +3, +4}dBm using
However, I am being asked...
hi support team,
customer had one problem about 9151 with esim: the iccid can't be readout, it should be 19 bytes string, but we only get 6
may i ask what could be the...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
I’m using the DECT Shell perf command to evaluate DECT NR+ performance.
Could you please clarify the units and scaling of the snr field in nrf_modem_dect_phy_rx_pcc_status...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Is there any point to using deferred logging with the RTT backend?
The way I understand RTT is that it writes the message to a buffer where it is fetched via DAP, skipping...