The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
hi, I have posted a detailed problem using Eclipse on Vidar's tutorial.
Any help is appreciated.
See following link:
devzone.nordicsemi.com/.../
Thanks!
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I want to send a data of length 1024 bytes over the ble UART , but the maximum length of data is 20 bytes at a time. Is it possible to increase the data length per instance...
Hello!
I try to use "ble_default_bootloader_app.hex" with my app to allow OTA option for my device. (nrf51822 and SDK 7.2.0) With NRFToolbox I can connect to the device ...
Hi all,
How can it be that sd_ble_gatts_sys_attr_set function returns BLE_ERROR_GATTS_SYS_ATTR_MISSING?
With the first and second connect it returns success but the...
I saw that each CCCD or sys_attr should be persisted per connection, does it mean it should be saved on flash to be restored during next connection for same device ?
and...
If iOS of BLE master sends 4 packets of the same write characteristics with MD bit in the same connection event, how does SoftDevice of BLE slave work?
The ble_event_handler...
Is there a summary of potential pitfalls, i.e. issues which are asked repeatedly by users in these forums regarding HW/Schematic/PCB design for NRF BLE chipsets. Making mistakes...
I just published my port of a new FreeRTOS operating system version for the nRF51x22 and the nRF51 SDK 8.x.x to github.com/.../freertos_nrf51 , the README is copied below...
I am trying to implement some write to flash, and started by integrating the relevant functions from the example code I found in this thread .
I added a dummy write function...
Hello,
I'm building an aplication with multiple nRF51822 beacon modules. I'm using dual mode S130 softdevice. Sometimes, when beacon recieves a lot of messages, and forwards...
I'm trying to erase the page 32 of a nRF24LU1+ via SPI (using a Bus Pirate).
What I did so far:
Display the first 16 bytes of content of page 32: 0x03 0x40 0x00 0x10...
I have a switch connected on the nRF51DK Board. The switch is connected on PIN25 and PIN 28. I try to read the state of the switch.
My setup:
-nRF51DK
-SDK8.1
...
Hi
I am making some low-power wireless sensors powered by coin cells, which will sleep for long intervals between readings/transmits. I am using the micro ESB libraries...
