When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hello everyone,
I'm currently developing a project that involves combining LoRa and maybe NB-IoT technologies. For this purpose, I've already been utilizing an nRF52840...
I have a BMD 350 nrf52832 module connected to nrf52DK board via P20 header. I am using nrf52DK to flash the firmware onto BMD350. my code works with nrf52DK and it logs onto...
Hello,
I am trying to factory reset 2 nrf52840 dongles that I had very long ago with unknow applications on the dongles. When I erased and installed the image of nrf_desktop...
Hi,
I would like to know how to write to the UICR OTP (0x00FF8300) in the application core of the nRF5340 at runtime. This procedure should be performed once at the factory...
Hello.
I have been successfully flashing the nrf52840 dongle using the nrfjprog comand. I have been successfully able to reset and erase as well. Recently however, none...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hello, Nordic Team,
I'm currently working on implementing a custom cluster in the Matter application. However, I've encountered issues where the methods described in your...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
