Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I see that there is a 1.2 Volt VBG reference available for the ADC but that reference doesn't seem to be available for the low power comparator. Is there any undocumented...
I'm developing a central providing NUS client services to multiple concurrent peripherals. I had code working reliably under SDK 9.0.0 based on the NUS client example in github...
Hi, we looked at your BOM for matching components in your file:
www.nordicsemi.com/.../15787782
for QFAC variant of the IC. You use LQP15MN27NG02D as 27nH inductor which...
Hello guys,
I am using this repo to update my device's firmware but after the update is complete, the iPhone cannot find the correct devices services anymore.
To detail...
We're using the NRF51822 and the S130 with V9.0 SDK, and we're using most of the features of the SDK for our Firmware; but I'm running into a problem flashing the device on...
I'm rolling my own very simple PWM implementation (I'm not using the PWM example code). My code is below:
#define GPIOTE_CHANNEL_NUMBER 0
#define PCLK16M 16000000
#define...
HI:
I use gzell protocol to realize 2.4G communication with SDK 5. I wonder that is the gazell protocol update in SDK9 or SDK10 ? and is there any improvement in latest version...
Hello:
I want use nrf51822's time/ppi/gpiote to capture the pwm rising/falling range duty.I want to know the most numbers of pwm channels duty parameters it can capture?...
Hi everybody,
as Nordic is currently working on this "Internet of things" thing and there are plans for an IPv6 over Bluetooth stack, I was wondering if it wouldn't be...
Is there a calling context restriction for sd_ble_gap_connect()? Either in the function call or where the peer address pointer is in memory?
I based my Central project...
Hi everyone,
I tried to test nRF51-ble-app-uart-static-passkey to learn the static passkey method.
I used PCA10001 EK board, with S110_7.1.0 and SDK_6.1.0.
Well, if I connect...
The maximum data length of a characteristic is 9, and I use the follow function to send the notification to a client
uint32_t dxs_send(dr_ble_dxs_t * p_dxs, uint8_t * p_data...
Hello,
I am debugging through UART with nrf52 and s132 softdevice using Keil V5 for the proximity app. When I flash the example app from the 9.2 SDK and look at the debug...
Is there a migration guide for the SDK 10 somewhere? I think the use of the APP_TIMER_DEF() macro is one thing that should be in it. Took me a while to understand why the...
