Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
Hi, I use the nRF52832 board (PCA10040 v1.1).
Before creating a custom PCB that uses nRF52832-QFAA, I chose
Q22FA12800025 FA-128 32 MHZ 8.0PF (load cap = 8pF)
and ...
This should not be a sudden my PCA10040.
Jlink are probably going to have failed.
It does not appear in the USB Jlink to appear as Atmel.
Is there a way to recover...
I am doing a project about nrf51822 smart beacon kit and a person has give me this link: infocenter.nordicsemi.com/index.jsp
to download the firmware and hardware files...
Hello,
I develop a BLE central device based on nRF52 (with the newest connectivity firmware and SoftDevice with API v3) and the pc-ble-driver in version 2.0.
Since my...
Hello Everyone,
I am working on nRF51 I need to save data with timestamp (current date and time).
Is there any example code is available so I can set current time and...
Hello,
Recently read about FIDO’s U2F authentication protocol for NFC and Bluetooth smart.
https://fidoalliance.org/fido-alliance-equips-u2f-for-mobile-and-wireless-applications...
hello everyone,
I am doing a project about Ibeacons. I need to make a selfmade bluetooth smart beacon (excuse me for bad English). I found a schematic circuit design of...
Hi all,
I am trying to get an Android Nexus 5X app to work with an NRF chip, and facing some problems, specifically with writing to a characteristic. Really hope to get...
Hi,
I discovered unusual behaviour in a SPI read transfer.
My transfer consists of writing one byte (peripheral register address) and receiving one byte (contents of...
