Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hi, I'm working on a project where I'm trying to make an nRF51822 play a basic sound (such as a beep). Is there a recommended DAC that should be used with this particular...
hi, i am using nrf51822 version 2, SDK 6.1.0, softdevice version 7.3.0.
because the nrf 51822 is version 2, i have no choice but to use SDK 6.1.0 not 11.0.0(latest version...
hi,
i am using ble_uart example for send 3 byte (midi format) of data over uart.
i am receiving data which is appended with past data and sends as a chunk of data around...
Hello, i'm making small android application for my own test purposes. I want to understand full structure of advertisement packet which i receive with my phone. I can't find...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
Hi,
I want to use nrf51 development board as a bluetooth alarm clock using internal RTC . How can I generate timestamps to determine current date and time. Can the timer...
hi.
i want to parse the data before sending to BLE UART.
i am fetching data from RX/TX pin. and now i want to do some modification in data before sending it.
this block...
Hi, I want to send a constant carrier during production testing of a product.
First I call sd_softdevice_disable(); then I do the following:
//Restart radio
NRF_PPI...
Hello,
in our application I can see, that sometimes the nRF51822 completely resets, during a BLE transmission.
I am using S120 as peripheral. The peripheral is connected...
Hello,
I am trying to understand the basic working principle of the bootloader so i tried the DFU example in the SDK 9 it gets compiled and when i try to flash into the...
Hello,
I am using BL600A module and Nordic softdevice and SDK9.0. The system is having NUS service and TX and RX characteristic. Now I have a requirement for firmware upgrade...
