Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello Nordic Forum!
I'm currently trying to load my firmware into my custom nRF52832 board without success. I'm using the nRF52DK (PCA10040) and the nrfjprog tool.
I...
Hi All,, please confirm me this .. please confirm i-beacon Rx + ble peripheral is possible ... Also please suggest me a development kit for the same which can be easily solder...
Hello,
I would like to move the SDK12.2 template example project out of SDK12.2 installation directory. How can I do that using uVision5?
I tried to change all the reference...
Hi
I don't understand how to correctly flash all three parts so that the app runs on boot.
At the moment if I flash them all the nrf51 (51822) boots to the dfu bootloader...
I can see in the latest SDK 12.2 that signing of the dfu firmware files is possible.
Am I right in thinking that this signing verifies the source of the firmware files...
Hi, I have nrf51822QFAA series. I am using S110 for softdevice which takes 96KB. My current program size is Code=31908 RO-data=512 RW-data=312 ZI-data=8360. I want to know...
Hi.
I am using the new SDK 13.0.0 and nrf52 chip. I am trying to set a whitelist with
the peripheral_template example code.
I think the whitelist is already enabled in...
I have made an ADC driver that (should) scan 5 inputs into a sample buffer using EasyDMA. On the END event the 5 samples are transferred to 5 ring buffers read by the client...
I've tried to upgrade the firmware using the DFU feature of the android nrf-toolbox app, but it returns the "REading file failed" error.
this happens only with my phone...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...
Hi everyone. I am working on a project while doing my undergrad in EE and am confused on a few things.
I am using Raspberry Pi 3s with the NRF24L01 (NRFL) chip and code...
