I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
Can any one Explain me the Following Error
GATT INVALID OFFSET in the Clinet(nrf master control panel APP)
I am getting this error when i try to send more than 23...
Hi,
we are designing a module with the nRF52832 WLCSP. As the module will be soldered on a motherboard a second soldering process respectively a thermal exposure will take...
I would like to load the blinky example on the nRF52 preview development kit. When I try to build the project I will get this error:
Error #541: 'ARM::CMSIS:CORE:3.40.0...
Hello, this question is similar to this questions (Scan request packet, answered by John DeWitt and Aryan)
I'm using
IAR EWARM 7.20
PCA10001 V 2.0.0 ...
We are using nrf51822 AB variant(16kb Ram, 128 kb flash). Due to flash size constraints we are still using s110 softdevice v5. Following is the linker script config:
FLASH...
Hi,
I have setup my system for working with nrf51822 with openOCD and STLink to program it. The blinky went well. But now when i try to program it i get the following error...
I have just concluded a three year development using TI's Tiva ARM M4 chips, writing both bootloaders and applications.
I am using an RFduino to explore BLE.
I have...
Hi all!
Today I run tests in a public place (some Art Design College) and it looks that radio environment, that exists in the place, kills nrf51 completely....
My guess...
Hello.
I want to flash DFU bootloader with keil on chip nRF51822-CEAA (256kB flash, 16kB RAM). I'm using s130
The areas i write to are:
IROM start: 0x3C000
IROM...
I was wondering if it would be possible to add an event for Service Discovery (and other similar BLE stack events) that could be detected by user applications. Per answers...
hello there i have two nrf51 dk kits. now i want that one act as central and other act as server.
i want to communicate between two. can you tell me how to do it??
i think...
hello all:
IN s310 multiprotocol--ble_ant_app_hrm example ,I open the macro BONDING_ENABLE, then i compile,there is a error
......\main.c(674): error: #136: struct ""...
Hello,
At the moment, we test the “Power Off” Mode for lower energy consumption of the nrf52 Preview Developement Kit (V1.0.0) in our project and I have a question about...
