Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I just converted over from SDK8.0 to SDK8.1 to use the pwm library. After I was done, I figured out by searching on here that the GPIOTE is drawing ~1.1-1.2ma in sleep.
...
Hello everyone
i ahve configured the button and i want to make the function like this press the button for 3 sec and then the device should start advertising can anyone suggest...
We are running tests using the spi_master_with_spi_slave example and using an oscilloscope to see if we are getting any signal from the clock or the MOSI but we have not received...
I want to use mcp(master control panel) for windows to search for ble devices and do dfu via bluetooth, how can tell me how to set up the windows and usb dongle?
this is my sec_param:
sec_param_bond 1
sec_param_mitm 1
sec_param_io_capabilities ble_gap_io_display_only
sec_param_oob 0
sec_param_min_key_size 7
sec_param_max_key_size...
Our present application makes heavy use of the nrf51822 UART and I2C interfaces. We have a 115200 baud UART channel and thus need HW flow control. We are interfacing to an...
I would like to create wearable fitness based applications/hardware using nRF51822. But i am not sure how to get the fullest of power down modes in the chip.
For example...
Hi,
I purchased an nRF51 DK recently.Followed this tutorial to compile and flash an example project:
devzone.nordicsemi.com/.../
Here are the tools used:
Keil...
Hello，greetings.
I am trying to communicate among 2 NRF24L01+ modules using stm32 and stc89c52.
With EN_AA = 0x00, EN_RXADDR = 0x00, SETUP_RETR = 0x00 on PTX ,and EN_AA...
Hello,
I want to use preprogrammed Long Term Key (hard coded) with Device Manager for nRF52. I found the dm_enc_key structure but I could not find any solution to provide...
Hello all
I have an nRF peripheral based on S130 SD. I have exposed certain services with both read and write permissions. However i would like to secure these services...
Hello,
I have developed a simple characteristic to send data over ble using the ble_nus service.
I created a service and added a characteristic to send. Then sending the...
I am working on a BLE device (currently being prototyped with the mbed DK). It connects to a smart phone app. I would like to build in some security features, definitely some...
