Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
hi,
i am using ble_uart example for send 3 byte (midi format) of data over uart.
i am receiving data which is appended with past data and sends as a chunk of data around...
Hello, i'm making small android application for my own test purposes. I want to understand full structure of advertisement packet which i receive with my phone. I can't find...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
Hi,
I want to use nrf51 development board as a bluetooth alarm clock using internal RTC . How can I generate timestamps to determine current date and time. Can the timer...
hi.
i want to parse the data before sending to BLE UART.
i am fetching data from RX/TX pin. and now i want to do some modification in data before sending it.
this block...
Hi, I want to send a constant carrier during production testing of a product.
First I call sd_softdevice_disable(); then I do the following:
//Restart radio
NRF_PPI...
Hello,
in our application I can see, that sometimes the nRF51822 completely resets, during a BLE transmission.
I am using S120 as peripheral. The peripheral is connected...
Hello,
I am trying to understand the basic working principle of the bootloader so i tried the DFU example in the SDK 9 it gets compiled and when i try to flash into the...
Hello,
I am using BL600A module and Nordic softdevice and SDK9.0. The system is having NUS service and TX and RX characteristic. Now I have a requirement for firmware upgrade...
Hello,
Should the application guarantee that the data sent to sd_flash_write is available until it receives the callback or will the softdevice make a copy of the data...
Do you have an example application which automatically re-bonds to an iPhone when the phone has been powered off and then powered on.
Otherwise, what changes are required...
