I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
What is the designed (/actual/required due to the specification) behaviour of the Bluetooth stack S110 when notification packets are queued and the CCCD controlling the attribute...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
bonjour , j'ai essayé de communiquer deux pca10028 en utilisant l'exemples " transmitter_pca10028 et receive_pca10028 " mais l'experience a echoué je sais pas pourquoi sachant...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS.
After connected the devices, iOS show confirmation to pairing.
When I canceled this or...
After enabling and starting the watchdog timer (RR0), how can it be disabled?
This following code does not work :
NRF_WDT->RREN &= ~(1 << WDT_RREN_RR0_Pos);
Neither...
Hi,
I use s120 stack and ble_app_multilink_central
I use function sd_ble_gattc_primary_services_discover(p_client->conn_handle, start_handle, NULL) for discover services...
The sniffer software doesn't seem to find the device on either of two different PCs here, and I'm not sure what we could be doing wrong.
The installation steps were the...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
