Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi Nordic,
I’m new to the nRF Connect SDK for VS Code and currently evaluating the nRF7002 DK board. I’ve been able to build and debug firmware successfully for the NRF7002DK_NRF5340_CPUAPP...
If you see i'm trying to install toolchain and nrf sdk v2.6.1 via vscode, the installations seems to be successful but at the end of toolchain as well as sdk installation...
Hi, In my project we are using the ESB between a nrf52811 and a NRF5340dk and are trying to evaluate the maximum speed we can reach with ESB packet transmission without acknowledge...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Advertiser...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
I just flashed a new image on my device using MCUmgr. In the logs, when the device boots up, it shows the correct APP_VERSION string.
returns:
I: Firmware version: 0...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
Hi, I am using nRF5340 for my unicast Audio server example where the nRF5340DK is the headset and my mobile device is the audio source. I have taken the unicast audio server...
Hi,
I just can not download nRF_DeviceFamilyPack 8.44.1 from this link developer.nordicsemi.com/.../ It comes up an error of the server. Does any body knows how to get this...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
