Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
i work with the nrf51 example for ble and sd130 (nrf51 dongle and sniffer) and now i like to use sd310 for ble and ant+. is there also a example for sd310 (or sd110)?
Th...
Hello everyone,
I am using ADC functionality with NRF51822 and its working fine, Interrupt is raising when ever i give input to Analog Pin. Communication protocol i use is...
Hello.
I'm trying to start developing with the nRF51822 Eval kit with Eclipse and ARM GCC but I ran into some problems when trying to run the ble_app_hrs_example. I've been...
I have enabled a gpiote module, it does not set gpiote_enabled to 1.
I have tried deleting the file in the RTE folder with no success. I have tried disabling and enabling...
Hi,
I would like to change the transmission power of the beacon kit so that I can switch back and forth between high and low tx powers for each set of advertising messages...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I'm exploring the ANCS example with SD130 SDK 8.1.0 ...
The application acts as a GATT client to receive notification from GATT server on the iPhone.
I see in the...
Hi everyone, I am now writing a program with scheduler. But the program always can't enter app_sched_execute. I don't kow the reason. Is the scheduler blocked.
Firstly...
Hello,
I'm trying to implement a DFU support into the application, and in order to learn how it works, I'm following the steps at the page developer.nordicsemi.com/......
Is there an easy way to find out the range of handles for a service which I added? Obviously the first one is the service handle, then you add characteristics and descriptors...
Hi,
While access sd_ble_gattc_write api, I got an error code 0x00000011. If I check nordic document for sd_ble_gattc_write error code, I can't find any error code with...
I would like to use nRF2460 in my project (Hearing Aid for elder people).In that I need to transmit the data from a mic/line in to >30 receivers within a range of 100 yards...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
