This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
Can anyone tell me, how the handle value is assigned for a profile. In my master control panel i can see the handle values assigned for every services, but it is not...
Use the beacon want to send with the temperature and remaining battery power.
But beacon of UUID, Major, Minor, Type, etc. The only information in the beacon 26Byte.
...
Hello,
We are developing an application which is using the app_scheduler (especially to put events etc.)
It seems that sometimes (very rarely) we detected a Hard Fault...
I have 4 buttons in my circuit with a nRF51822QQAC (a RAYTAC MDBT40 module on a custom PCB), I am using a very simple printf to check which ones are pressed, the internal...
I've followed this for assistance, but I'm stuck:
https://devzone.nordicsemi.com/question/17846/nonvolatile-memory-access/
I can read from flash, but I can't write to...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
I went to so many references and definitions of variables and functions but I can't seem to find where is decided to use either spi_master_0 or 1.. where is this magic config...
I am a freshman. And I am doing some research on BTLE by nRF51822-EK. I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Is there...
Hey,
For my project I wrote and tested (w/ nRF51 DK) all firmware in mbed. I also made a custom PCB w/ the nRF51822 CEAA chip based on the 4 layer reference design provided...
HI,all!
I want to know if BLE can send data to APP in form of String instead of Byte?(the examples all send in form of byte )
If it does can, can you mainly introduce...
Hey everyone,
I'm trying to print floating point numbers to the UART to debug my application. I know the nrf51 is doing the operations correctly because if I convert the...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
