Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi,
For providing OTA function , I add dfu service into my own application APP1. and create another application App2 to copy the new firmware(named APP3) and cover the flash...
Please help me !
(spi_maseter_config.h at line 29)
#define SPI_PSELMOSI0 20u /**< SPI Master Out Slave In GPIO pin number. */
nRF51822 QFAA Package pin no.20 = P0.14...
I'd like to use 'Direct Advertising' to get the attention of a Central (a specific one or any in range) when an event happens on the peripheral. Is this mode supported by...
Hi,
I hooked up an nRF8001 (Olimex) to my logic analyzer and am observing the behaviour of the RDYn pin.
After resetting the nRF8001 through the RESET pin, the RDYn...
Hi All,
Just got my NRF51822 development board today and cannot get the heart rate demo from SDK to work. Two issues:
1> The PCA1004 board (the one without antenna)...
Dear Sir, We are intending to develop wireless UART- BLE module for our wearable product (Cable replacement profile). Please, help me to get to know about UUID and cable replacement...
Is sd_ble_uuid_vs_add available over the serialzation interface? How can we add a custom vendor ID over the interface if there isn't a serialzation function for it here ?
Hello,
I have made some current and timing measurements on the nRF51822 Development Kit (connected to a nRFgo Starter Kit) running some of the example applications provided...
I would like to drive an LED from the nrf51822 gpio
How much current can the nrf51822.
How much current can the nrf51822 gpio supply?
Is there a recommended LED for...
Hi. I am using a nRF8002 DK, and i am working with nRFgo Studio for 64 bits, in a windows 7 and windows 8 computers (for testing of the error purposes). I am having serious...
How to set READ property to a characteristic pipe through nRFGO studio.Actually i am not able to set READ property to any pipe.How can i do this?
Because i want iPhone...
Hi:
I use TIMER compare function, I open four channels and every channel produce interrupter.Here are some of my code:
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1->CC...
Hi. I've never asked a question here, and I'm a complete beginner to embedded programming, so I apologize if I break protocol in anything I do on here.
My setup:
nrfgo...
HI,all!
I have a question about downloading program into nrf51822 MCU.
That is:
As you konw, using the nRFgoStdio to download the code, you have to download the softdevice...
