Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I'm using 51822 to control GSM module via UART (57600, no flow control).
My device is USB and battery powered.
After I program the chip I HAVE to disconnect all the...
Hi Team Nordic,
Any plans on supporting an official build-setup via Xcode on mac?
Since it's basically more about a way to quickly "git clone" a project + sdk's & softdevice...
I'm trying to upload ble_app_beacon example from SDK 9.0.0 to a beacon board (PCA20006) after successfully uploading it to a DK board (PCA10028).
My first step was to connect...
I have created a customized Services according to nAN36 Document.
SDK using 8.0
Stack S110 8.0
DEV kit PCA10028 nRF51.
J-LInk RTT DEbugger
When the function...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Is there a step-by-step setup for the nrf52 developer kit for Mac (OS X)?
For example, when I connect my DK board, it does NOT appear as a USB drive which is the very first...
I've read through the 'streaming' posts and my need is a little different. I only need about 30 kbps streaming. I've created a service of this but am quite new to BLE and...
Hi all,
Is it possible to check whether there is an active carrier with the nRF24L01+? I've got the TX and RX chips configured via SPI correctly (I think), yet I can't...
What do I need to take care of when I solder CE pin to VCC? (to save I/O)
NRF is mostly in RXing state, and sometimes TXes.
So far I figured out to go from RX->TX mode...
Hi,
Can I use RTT to build a communicate to a command line interface (CLI) in the device?
This would require that the program does not block, as it does in SEGGER_RTT_WaitKey...
I'm using the UART application in nRF Toolbox Version 2.4, iOS 8.4 on an iPhone 5S.
Is it possible to save the logged data to a file, or in any other way get the data out...
Hello,
I am using an Eclipse GCC environment with the following setup:
Ubuntu -> 14.04 (Trusty Tahr)
Eclipse IDE for C/C++ Developers -> Version: Luna Service...
kit: RF51DK.
sdk:nRF51_SDK_8.1.0
SoftDevice:s110_nrf51_8.0.0_softdevice.hex
I want to use 5 channels pwm to control 2 servos and 1 motor;each servo uses 2 channels pwm...
I included the DFU service in my project. With the MCP on my computer it is working fine.
But when I try to perform the DFU over the MCP(v.3.4.1) app on my android device...
