Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Is there any Nordic Sermiconductor Wireless 2.4Ghz product through which i can communicate with other wifi (IEEE 802.11) and Bluetooth devices ? At-least the device must obey...
Hello Community,
Does anyone know how to read/write configuration registers (UICR, FICR) on nRF51822 in a linux environment ?
So far, I have to stick with Windows for...
Hi
Please tell me someone about the causes and countermeasures!!
I Connect the board & JlinkLite and tried the flash write.
Softdevice Ver6.2.1 -> Success
Softdevice...
Unfortunately, I'm not seeing NRF_EVT_POWER_FAILURE_WARNING events on my s210 based system. As I've seen in other questions on the forum, I've implemented the calls below...
I'm currently trying to merge the S120 softdevice with the compiled code from the ble_app_multilink_central sample under Linux (Ubuntu).
Here is the command I'm executing...
There are a couple problems with the SDK 7.1.0 implementation of nrf_delay_us for GCC. The experiments I've run show the provided version generates delays 40-50% too long...
Hi,
I am developing an application to capture data on a PC over ANT+ using the ANTUSB-m as slave and the nRF51 DK as master.
In order to test my program I want to be able...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I am trying to use the nrf51822 to send media button commands over HID. I have seen several questions on here and they usually involve the HID Mouse example (which doesn't...
Hello,
I have been trying to implement AES in order to encrypt a time stamtamp to be sent in the advert of the iBeacon ( 128 bits, using Minor and Major bits, (16+16)*4...
Hi,
I am trying to decrease circuit power consumption that's why I am using sd_ble_gap_tx_power_set(TX_POWER_LEVEL) function. When I set TX_POWER_LEVEL as 4 or -20, I dont...
We are looking to change tx_power setting to Neg30 dBm and for this we have accessed NRF_RADIO->TXPOWER = (RADIO_TXPOWER_TXPOWER_Neg30dBm << RADIO_TXPOWER_TXPOWER_Pos);
...
I have the NRF51 DK working with CrossWorks on OSX. I have the blinky example working.
Now I would like to figure out how to get very basic HELLO WORLD type demo to iOS...
I am implementing dual bank DFU on the PCA10001 board using the latest SDK (7.2.0) and S110(7.1.0). I am able to enter bootloader from my app as detailed here:
developer...