Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello, question about mcuboot, particularly the imgtool.py.
When I run west build, the build eventually fails on:
Error: Image size (0xbac8) + trailer (0xc30) exceeds...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
I'm having some trouble connecting to the onboard jlink with the NRF9151 devkit that I've recently received. The quickstart seems to detect the NRF9151 dev kit, but when I...
Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
