Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Greetings,
we developed a custom board with a NRF9160 last year to be used with NB-IoT (LTE-M as Fallback) to communicate over HTTPS with our Servers. Now this worked quite...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
I have set up the OTBR with a RPi 5 and an nRF 52840 DK as an RCP. The CLI device can join the thread network as a child, the OTBR as the leader.( https://www.youtube.com...
Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
Our company is in the process of developing a new IoT product for LTE-M and NB-IoT. The sample application lwm2m_client runs fine on our devkits nRF9151DK & Thingy91 and connects...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi
I am trying to mugrate my app from v2.6.1 to v.3.0.2.
As I have several configuration variants, so I build from batchfiles, ending in a west build command. Updating...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
Hello!
I'm taking some performance metrics for encrypting data on my nRF52840 device and I was wondering if you might be able to help me. The goal is to see how long and...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
