Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi Nordic team,
I'm trying to stream audio from the nRF5340 DK to a BLE headset ( Sony inzone buds) using the [ Unicast Audio Client sample ] with the BAP profile.
Initially...
Hi everyone,
I'm using the nRF Connect SDK 3.0.2 and the nRF Connect Toolchain 3.0.1 with the matter ‘light_bulb’ example. I just want to do the following: 1) Get exactly...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hello, question about mcuboot, particularly the imgtool.py.
When I run west build, the build eventually fails on:
Error: Image size (0xbac8) + trailer (0xc30) exceeds...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
Hello Nordic Support Team,
I have three queries to make.
Is it possible to force the channel in which the data transmission is happening using nRF52840 DK.
To explain...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
