Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
I am using the "Nordic Uart Service", example to create a simple serial console which allows a user to change settings such as tx power, advertising intervals so that different...
As in the circuit diagram attached where the pin resource is insufficient For one Pin (AMULTI), I design gpio for Button and analog input as 2channel. (This switch uses the...
Hi DevZone,
I am going to apply a Arduino CAN bus shield onto nrf528400 preview DK. I was integrated this shield with Arduino board and a 3rd party BLE module. Now, I am...
I'm basing my PCB design on Nordic's reference layout. The product I'm developing will only be used for research, and is basically a one-off design. How closely do I have...
Hello,
I am using the NRF52832 for advertising every 10s.
However while entering the sleep phase, I noticed some glitches while measuring the current. You can find attached...
I am in need of some guidance around how to simulate multiple devices, with different addresses, on the same NRF52
I am currently developing a test application using the...
Hi,
(SDK 14.2 , S140 v5.0.2-alpha)
I followed the example in sdk v11 multiactivity_beacon : \examples\ble_peripheral\experimental_ble_app_multiactivity_beacon\hrs_advertiser...
I am using the nRF5_SDK_14.2.0 with two PCA10040 boards. ANT+ HR simulate from ANT+ simulator tool with ANT+ USB dongle.
Test 1 : SDK sample ble_ant_hrm_pca10040_s332...
Hello.
I have a situation that when upload the softdevice, application and bootloader for some reason stays in the bootloader after some debug I found that we enter in...
Hi,
i'am using nRF52840 (S140 v 5.0.2-alpha) DK and SDK 14.2.
i'am trying to create an application for Beacon which can advertise on 2 different MAC adresses, is it possible...
