Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello,
I am using NRF52840 board and SDK 14.1, Softdevice 5.0.0-2.
I am testing other devices on my board. However, it seems to work normally until 2, but the connection...
Hi,
I just try the new mesh SDK V2.0.0. And I found that there is an error if I compile the "examples\light_switch\proxy_client" more than one time.
The error is here...
Hi,
I have successfully flashed nRF24LU1+ via ISP. Right now, I am validating using USB to download firmware for future production. Here is the issue.
Our project has...
Hello all,
I'm currently working on a project with a due date coming up soon. I'm using two (2) nRF24L01's with a nRF24L01+PA+LNA shield.
Right now I have my micro controller...
I want to change the advertising data of the advertising packets with time. I did find the solution for the same in this link - https://devzone.nordicsemi.com/f/nordic-q-a...
I have a board with an NRF52832 and an LED driver. I wrote a function that bit bangs a serial stream to an LED driver. It works when I use the nrf_gpio.h library.
However...
I am working with NRF 51DK. I am trying to flash a software on the target device which uses NRF51 microcontroller. I am using NrfGo studio. I am facing an error that, Unable...
Hi All,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello, everyone!
I am a newbie developer about nrf51.
I need to advertise my BLE and save my power.
I have read the document that nrf51 has System-on (including some...
We have a couple of development units that are showing the above error in the nRF Toolbox app. Using the nRF Connect app, the DFU dialog just goes away and the screen reverts...
What is the difference between 'NRF_SDH_DISPATCH_MODEL_INTERRUPT', 'NRF_SDH_DISPATCH_MODEL_APPSH' and 'NRF_SDH_DISPATCH_MODEL_POLLING' in the 'NRF_SDH_DISPATCH_MODEL' related...
Dear All,
Currently I'm developing a BLE module that will be useful by its uart service and will use nrf51822. Nordic provided an example based on sdk 6.1 for low power...
Hello,
I want to read data from mesh network (from all the servers) to send it to a gateway. I saw in the documentation that Provisioner s can be a part of gateway devices...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
