after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
These posts indicate there was a problem at least at one point with the S132 SoftDevice erroneously requiring FPU:
https://devzone.nordicsemi.com/f/nordic-q-a/8133/nrf52...
On line 301 of app_timer.c there is the following code:
// No more timers in the list. Reset RTC1 in case Start timer operations are present in the queue.
if (mp_timer_id_head...
Hello,
I completely don't understand how to increase the packet size in the ble_uart example (using SDK 14.2 in both sides)!
I have two NRF52 DK boards and nothing is...
Hi all,
I'd like to design using 2ch SPI of nRF52832(as a MCU).
So, How many SPI channels of nRF52832?
And, Inform me pins of SPI port of nRF52832.
Best Regards...
Hi
I am creating bond from the Nordic device to my Android APP.
But I want to change the name of the device immediately after the bond has been created.
i.e from NEWDEVICE...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hi,
Just a quick question about how the ble_app_uart works.
When sending to the UART from "static void nus_data_handler(ble_nus_evt_t * p_evt)" and also receiving from...
Interrupt or main() context, or something else?
We're using S140 SoftDevice, nRF52840 and Segger Embedded Studio 3.30
We're also usinq Quantum Leaps ( https://www.state...
Hi
I am use hids, ancs and hrs services together with bonding. Phone should hold the connection with device. I am enable heart rate sensor when notification is enabled ...
Hello,
Trying to make GATT services configuration for nRF8001 chip in nRFgo studio. On services.h file generation I see Generation of source files failed window with "Generate...
Hi, Nordic team:
Now, I'm using NRF51822QFAC in a production with the SDK 10.0, the firmware includes FreeRTOS and DFU, when start the DFU in nRF-Connect APP, it can't jump...
All standard SDK examples disconnect immediately once I try to connect to from Android device. But when I flash the same sketch to nRF52-DK, I can connect successfully.
...
