Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
Hey ,
I'm trying to implement a device that waits for the clicks from the user and sends it over ble as notifications.
i have written the header files for sensor . and from...
im trying to get my nrf51822 connecting only to my phone, I set the phone mac address on white list, but I cant connect to my phone (android) wiht nrf master control.
How...
When my program hits an error returned by an NRF API call, I get a hex number corresponding to that error from the app_error.c:
case NRF_FAULT_ID_SDK_ERROR:
m_error_data...
We've got devices that are out in the field which were built on SDK6.1 w/ 110 SoftDevice 7.1.0 on an nRF51822.
Went with the dual-banked solution as that was what was available...
We are developing a blood glucose meter based on the nRF51.
To comply with Bluetooth Continua, do we just implement the Glucose Profile and Service (GLP and GLS)?
Do you...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
Hello,
I would like to know about the possibility of programming the nrf51822 with a Keil ULINK-ME Debug Adapter (or, if necessary, Keil ULINKpro) instead of the recommended...
Our product has a legacy interface and for security reasons I want to allow users to disable or enable the BLE via this legacy interface.
My approach to this was to disable...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hello,
I am having much fun with nrf52. I'd like to implement SPI read (few bytes) per GPIOTE event over PPI, the source is the GPIO event and the destination task is a...
Hi,
I'm working with the nRF51822
I'm trying to enable the use of some timer callback on the ble_app_template.
I've succefully created and started all the timers, but i...
I have a modem connected to some pins on an nRF51822 on a custom board. Two pins on the modem are active low. One is a reset pin, the other a VCC control. I want these pins...
