Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
The problem is exactly same with the topic. I have custom board for Beacon. At the beginning I soldered 5 boards and all of them was working perfectly. After few days, 4 of...
One of the features of our product is the ability for a user to rename their device. I have tried to implement this with the sd_ble_gap_device_name_set(...) and ble_advertising_restart_without_whitelist...
Hi,
Would it be possible to change this setting (Relay) dynamically, i.e., instead of changing the value of m_relay_enable in the network_init() function and program the...
I'm using this code to log the BLE MAC address on my peripheral device, an nRF51822.
void ble_log_mac_address(void)
{
// Log our BLE address (6 bytes).
ble_gap_addr_t...
Hi,
I'm basing my project on ble_hrs_freertos example project (nRF52832, SDK14.2, PCA10040)
When calling assert(condition) in the original example project, it works...
Hi!
We are evaluating the 52832 soc for use with a DALI-controller. The communication speed with the controller is at 1200 baud, Manchester encoded. Is it possible to interface...
In BLE communication, I want to send 244 bytes of data from the peripheral to the central every 50 ms, is it possible? If possible, please tell me the setting method.
Hello, I have a problem with the configuration of GPIOTE low accuracy pin interrupts. My code is running on nRF52832 and already uses ble stack, PWM1 and PWM2 instances with...
Hi,
Right now I have a program on nRF52-DK (SDK 11) that scans for BLE adv packets, and transfers data from some specific addresses to PC through UART. Around every 10ms...
I'm attempting to use the PPK with the nRF52840 PDK with no success. I'm getting nothing running the nRF Connect with the Power Profiler. Configuration is as follows:
nRF52840...
Hey Guys,
Have been playing around with various MTU sizes to better understand throughput. I'm curious about one scenario though. Let's say for example that we are using...
Hi
We are using a slightly modified (but fully compatible signed bootloader) in out product. On the application side we have a C# implementation of the DFU protocol that...
Hello there,
In my next project I need a data link similar to BLE classic (like the HC-05 module) and it needs to respond with an app API fast and push data rather then...
Hi,
I'm following "ble_app_uart_c" example and works very well with SDK 10.0.0. So now I want to communicate with HM-10 module, but this has one Tx/Rx Characteristic. Are...
Hello,
In my quest to monitor the activity of hundreds of nodes (directly addressable), I am facing quite an obstacle.
The small memory of the nrf52 (nice piece of hardware...
