Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi Nordic team, I'm currently facing a bit of a snag while trying to establish communication between the nRF52840 (NCS 2.5.0) and the MS5540C sensor using a 3-wire SPI protocol...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
I want to add custom outputs to my custom board dts: this thread mirrors exactly what I'm doing:
https://devzone.nordicsemi.com/f/nordic-q-a/92813/how-to-declare-a-single...
Currently advertising packet is built by macros, but the data types include const qualifiers.
What is the "proper" way to dynamically update advertising please? I need to...
Hi, I'm using the nRF52840 to measure voltages through the SAADC . I'm observing a measurement noise of around 80mV peak-to-peak on inputs AIN0, AIN4, and AIN5 .
Here are...
Hi,
In our devices, we use an NRF51422 chip.
In our software we use the S210 v3.0 version of the ANT softdevice. I am trying to find the anomaly list of this ANT softdevice...
Hi,
We developed a custom board based on the nRF54L15 SoC. We realized many current consumption tests with regulator configured in DC/DC mode. These measurements are in...
Hello everyone,
I'm currently developing a project that involves combining LoRa and maybe NB-IoT technologies. For this purpose, I've already been utilizing an nRF52840...
Hi, I'm using nRF Connect SDK (v2.1.2) with VS Code on Windows for a project targeting nRF52811 .
Even though everything is versioned in Git, I keep running into the following...
Hi,
I have an issue with VS code. The connected devices does not show my jlink debugger nor the DK. However, nrf connect desktop programmer shows them.
Toolchain: v2.6...
Dears,
I made module with nRF52832. And I made also custom board with the module.
And then I tried to write FW(ble_app_uart_c_pca10040_s132.hex) but timeout error occurred...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I'm using nRF connect SDK2.9.0. I don't create my threads. Instead, I have a GPIO interrupt and a k_timer interrupt, each doing their own job.
In my timer expiry function...
