Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
When I build my first blinky sample, I met a error and correct it with ( https://devzone.nordicsemi.com/f/nordic-q-a/120279/update-to-ncs2-9-1-compilation-error/529668) ....
Hello,
We use NCS2.9.0 and NRF54L15-DK do the matter development, and we use template demo, just enable CONFIG_CHIP_DFU_OVER_BT_SMP in root prj.conf, then we do the ota...
Hi,
I am currently evaluating the new nRF54L15 DK development kit.
I installed VS Code v1.96.4 with nRF Connect for VS Code Extension Pack v 2024.9.5 . I am currently...
Hello,
I'm trying the Thingy 91X but I'm having a few issue with the demo application that connects to hello.nrfcloud.com:
After flashing it with the Quick Start from...
Hello,
I have a custom nRF52820 board powered by a coin cell, and I want to measure its power consumption using the Nordic Power Profiler Kit 2 (PPK2).
Could you please...
I met some problems when add build configuration to my first application. I used the blinky sample template. And the device a nRF5340 DK. My PC can detect my devices. But...
Hello everyone,
I'm working on a project based on the nRF52840, and I'm using nRF Connect SDK 2.9.0. The project uses MCUboot, but the firmware image is signed externally...
Hello, I am using NCS 2.9.0, an nRF5340, custom board files (see attached), and no external flash and I would like to use simultaneous DFU over BLE. I believe this should...
Hi,
I'm currently using “light_switch” to enable BLE NUS, but every time the device reboots it needs to be re-paired, I checked the serial logs and found that the pairing...
HI there,
I am using keil pack installer. but found the download link is broken:
" ">developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.40.3.pack...
Hello,
I'm using central_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT log...
Hi all,
We are looking to use the nRF9151 and we are trying to determine estimated certification costs for US deployment
So, if anyone can help or knows:
What pre...
I've been using the ppk2 power profiler with version 4.0.1 for over 2 years and it has worked very well in providing a power source and monitoring/ with reviewing the power...
Hi, I'm currently working on adding DFU over UART to my firmware running on an nRF52dk/nrf52832. To have a minimum viable example, I'm trying the DFU over UART exercise sadly...
Hi Support Team,
I met a conflict situation. Could you help give me some guidance?
The project is based on nrf5340 and ncs V2.5.2. The device supports BLE FOTA and works...
