nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
zephyr\subsys\bluetooth\mesh
zephyr\subsys\bluetooth\mesh\shell
I need to use APIs for certain files in the path mentioned above. Currently, I can only copy the files...
Hello,
I am experiencing an issue while trying to connect an external flash memory (MX25R64) via the QSPI interface on an nRF52840-based custom board. My pin configuration...
Hello.
I tested the DFU distributor sample using two nRF54L15DKs. I have three questions.
1. Apply is not completing. The firmware transfer seems to have completed, but...
hi support tean,
customer is asking about " Credential storage management %CMNG" in our modem, how to calculate the hash value
i have put the log in below:
[12:33:32...
Hi Sir ,
I am running the nrf/samples/bluetooth/direction_findinding_connectionless_rx App on an nRF52833-DK with nrf Connect SDK 2.7.0 and toolchains v1.6.0 version.
...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
