hello everyone,
I built an application based on the peripheral_uart sample running on the EV-BM833 board. The application includes the Nordic UART service.
Using the nRF...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
When using the shell_module project of SDK v3.0.1, I changed uart20 to pins p2.0 and p2.2, and the serial port printed garbled text.
Below is my overlay file:
Strangely...
Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi, I am seeking assistance with a very weird issue encountered while programming an nRF5340 SoC using a custom debugging-PCB using a SEGGER J-Link EDU debugger.
The debugging...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
Hi all,
I have a custom board with an 9151, I want to use mqtt with aws, it's works I'm able to connect aws, but I have a question about
If I want to be able to connect...
Hello Nordic Team,
I am requesting clarification on the capabilities of my nRF9151DK to be used as a debug and flash probe (via the 'debug out' P20 headers), and compare...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
I am developing a new architecture for my project. So, I am getting data from the peripheral, a custom nrf52832 card. Also, I create my custom service to send data and add...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
Hello Everyone,
I am using NRF52840 dk evaluation board Arduino ethernet shield which has W5500 ethernet chip and for my development purpose using SDK 2.6.1 on visual...
