hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
I have read these the following posts:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
But, most of the answers are quite old. I am wondering if the solution...
I've seen several similar questions -- none of which were concerned with the bootloader project.
I believe the linker is looking for sections called .noinit and .bootloaderSettings...
This is slightly off topic (I also posted this in the mbed forums), but I hope maybe someone here would also know.
My goal is to use the newly secure boot loader that was...
I have Inited the pstorage
err_code = pstorage_init();
APP_ERROR_CHECK(err_code);
Here PSTORAGE_NUM_OF_PAGES=2(1page for bonding ,1page for my application use )...
hi,
I am working with nrf51822 development board using Softdevice(s130) and sdk 11.0.0.I implemented whitelisting in ble_app_uart code but it's not working correctly.Once...
I'm using the example bootloader from SDK 12.1.0 with gcc, nRF51822, S130. I flash the SD, bootloader and my application in that order like this:
flash: all
$(NRFPROJ...
Hi,
IAR ARM 7.60.2
Nrf52
Softdevice 132 v3.0
SDK 11
I am trying to use SPI with easy DMA. I have implemented the PAN 58 workaround for sending 1 byte but it fails...
I got started with bluetooth learning. But it's too hard to understand ble protocol. Do I have to learn BLE protocol even If my purpose is only ble communication with simple...
Hi,
Could someone help me about the following questions?
Q1: What are the connection parameters set by the Android app nRF Connect? Can I change them?
Q2: How can...
I have a bit of a strange problem.
I am designing a signal Gazell signal repeater.
It listens in host mode then sets itself as a device to pass the data along.
However...
Is it possible to put the nRF52 into recieve only mode (say through direct test mode) so that the input impedance can be measured using a VNA? Is the input impedance of the...
When I initialize PPI after timer1 has been initialized I get a fatal error (and reset).
Code:
const nrf_drv_timer_t timer1 = NRF_DRV_TIMER_INSTANCE(1);
nrf_ppi_channel_t...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
