I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I want to use spi list feature without ppi. Is that possible?
Because I have to use the same spi module for OLED, SPI flash and accelerometer with FIFO, spi ppi...
Hi There, PCA10004_Schematic_And_PCB.pdf
We are working on Nrf51822 chipset and have observed in our case that once we download the code we are able to discover the device...
What I am trying to achieve is single-file executable for nrfutil tool, for performing DFU.
I downloaded sources and built it using pyinstaller. I can succesfully create...
Let's say I have my android phone connected to the nrf52840 device via bluetooth,
and let's say I change preferred phy from 2 Mbps to 125 kbps, would the connection with...
in my case sdk10.0.0 and I can not update sdk.
please help me to write sd card. if file system not possible ,please explain how to write raw data like sensor value 1000 time...
nrf52832 sdk12.2.0 s132.3.1
Hello.
Can't write properties after flash experimental_ble_app_buttonless_dfu example into chip.
I can only enter into bootloader using button...
using mbed uartservice on micro:bit. connects fine to nordic toolbox uart on ipad
is it possible to connect to puTTY or similar on windows using csr 4.0 ble dongle.?
win7...
My question is can the beacon be activated by someone shaking it and receive a notification via Bluetooth? If so what is the range it would have? If not can an additional...
Hi,
I am connecting the AKU242 straight to our microprocessor. It is a PDM interface so it has a SELECT, DATA, CLOCK, VDD and 5 GND signals. On the datasheet, there are...
I am about to implement the secure DFU on our custom board using SD132 V3.0.0 and SDK12. When I worked with SDK11 I had to make a bunch of changes to the bootloader to work...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. I started building off the ble-app-hrs in the examples of the documentation so my code is pretty...
Hi,
We're trying to port and migrate our nRF51 SDK v8 (softdevice s110) codebase to nRF52 SDK v11 (softdevice s132), but we're seeing a crash occur (goes into HardFault...
Hello,
Can anyone help me figuring out the best possible way to store certain characteristics which I want to never reset values on the events of controller RESET or power...
