Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hello,
I use SDK v2.9.0 with nRF52840 and my application is based on peripheral_uart example.
Have I understood correctly that nRF52840dongle has preloaded (by Nordic...
Hello,
I’m currently working on a Bluetooth Mesh project using Nordic Semiconductor devices, and I would like to get guidance on static provisioning and group-based communication...
Hello,
I'm working on a project that uses the Serial LTE Modem (SLM) application on a custom board. The main processor sends data to the nRF9160 over UART. The project is...
Hi,
I am currently working on evaluation of the nRF52810 for a simple project which requires a very low power consumption. I searched and found an example which I modified...
I have a class that wraps the Zephyr implementation of a mutex. For some reason, when the code runs, I get this error: ASSERTION FAIL [mutex->lock_count > 0U] @ WEST_TOPDIR...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Hi,
I am working on RF testing on the custom board.
I have configured the nrf UART TX in p1.04 and UART RX pin in p0.13.
UART TX pin is working fine, but the UART Rx...
Hello - Above is an error message I am encountering when attempting to use the NFC record_text sample code for a nRF54L15DK in TF-M as the Secure Environment.
The samples...
Hello.
This ticket was derived from another ticket .
I have a few questions about hardware-based downgrade protection.
About the Downgrade Protection of the Network...
Hello!
I’ve been learning about Bluetooth Mesh recently, and I’ve been testing the sample at nrf\samples\bluetooth\mesh\chat , but there are still some parts I don’t quite...
I'm using these devices for a personal project, I'm an experienced software engineer but relatively new to MCUs, I know this is a legacy product from Nordic's standpoint but...
I'm an experienced HW engineer with minimal SW experience. I just went through your SDK fundaments with an nRF52840DK to get acclimated to your SDK and brush up on some C...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
I am a beginner to BLE Communication ,
Currently I am working on a project where I need to connect a peripheral device ( Central (nRF52840) ---> Peripheral (BLE device)...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
