Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
This is what I believe, of course, my beliefs are flawed, so please DO point my errors out:
There is this attribute table on server/peripheral devices. The actual...
Hi，Nordic
I have one nRF24LU1P device, when I make it as USB Dongle, I will use :
hal_usb_endpoint_config(uint8_t ep_num, uint8_t ep_size, hal_usb_cb_endpoint_t endpoint_isr...
When I repeatedly (>290 times) send the same notification to the connected host via sd_ble_gatts_hvx, I get a sd_assertion:
Fault identifier: 0x1
Program counter: 0x104FA...
Hello,
I have a custom board which has NRF52832 SOC(i.e. main MCU) and another ARM Core-M0-based MCU(i.e. target MCU). These two are connected over I2C. I wonder how to...
nRF BLE sniffer is crashing within the first few minutes of use. Attached is the log of one sniffer
session from the start to when it crashes.
Here is my log.txt from...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
I have device with nrf5x and I will customize this device on production. I use to flashing nrfjprog.
Will prepare one hex file and customize e.g serial number during flashing...
Good time dear Engineers!
Faced with a general Problem.
I use two nRF52 boards connection : Central <-> Peritheral.
init data: MIN/MAX conn intervals = 10/30 ms
...
I noticed that the GPIO port read and port write for SDK v12.2 changed to accommodate chips with more pins but I can't find much information about it. How do I use nrf_gpio_port_out_read...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
