I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi, I want to add DFU to ANCS example.
I use SAMSUNG GALAXY Note5, nRFToolbox, SDK 11, nRF52832, softdevice 2.0.1.
Bootloader project I use is : nRF5_SDK_11.0.0_89a8197...
Hello,
I am working on ota ble_secure project. I have created a zip file which is the last step and copied this file to my smart phone so that I can upload it using nrf toolbox...
Apparently you need to set the CCCD handle of your target characteristic to enable notification. Problem is, how do you do that? I now know at least 2 ways to do that, one...
Hello!
I am using application that support ANT+ and BLE, so i am using s332 softdevice.
now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v12.2.0...
I am using the nrf52 development board, when I try to connect to one of its pins a signal from a sensor that generates an interrupt signal every 1ms the programs stops or...
Hi,
I have relay board which is attached to the SoC module nRF9E5 and also microchip serial SPI EEPROM 25AA320 is also attached.
I have the EEPROM programmer and I am...
Is it possible to connect more than one device over bluetooth to single router (Raspberry Pi 3 under archlinux)?
I connect using commands:
echo "connect 00:4D:25:16:1A...
Hi Nordic team!
In my company project, we are using the NRF52, and, apart of other peripherics, we need to use the NFC.
As the NFC isn't always exchanging data with the...
Hi all, As I known sdk13 have bluetooth 5 features that means we can send more than 31bytes in advertising data (8xdata) right? I'm using nRF52832 and softdevice s132 v5.0...
hi,
i'm not able to have the nRF24LE1 go to sleep. I'm using the example at the link below, to which I've added code for UART and ADC usage. Is there a way to end the...
hi
i am working eclipse for setting up projects for nrf52832. When i build the blinky example there is no error but the headers nrf_delay.h are not include and the LED_LIST...
Hi,
I want to write flash using received data in BLE interrupt handler(on_ble_evt()).
When i received some data from BLE, i try to write it to flash and wait until done...
Hi
I'm trying to use the nRF52840 USB Serial UART device (aka USB CDC ACM) however I can't find a Windows driver for this device
The VID is 0x1915 and the PID is 0x520F...
