Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
Hi,
Can any one tell me, what will be the current taken by internal flash of Nordic for
write and read operation and what will be the max time nordic will take to write...
Can someone familiar with the nRF51822 timer infrastructure confirm for me what the maximum achievable PWM frequency is, assuming 8-bit resolution? I've been weeding through...
We got the new sdk and ported the "Alert Notification Profile" to the EVM board. It can communicate with the the Master Control Panel. We want to know whether it can communicate...
hello, on my board the nrf24l01 is optional.
what is the preferred solution to identify if a nrf24l01 is present.
I tried to read the status register. But sometimes...
I am using Laird Bluetooth-4 device BL600 with smartBASIC. While communicating over the I2C bus I am encountering the Hard Pull-up on SDA line. During the Slave ACK I could...
The new pstorage abstraction is almost using 1K RAM, which I'd actually planned to use for something else :-)
Is it possible to limit the RAM used by this module. Can I...
Hi there
can I download the source code?
This app is able to detect the nrf51822 chip even with android 4.1, which is great, so I could test my firmware on my samung...
Hi,
We have a custom board with nRF51822 chipset, We have developed the code to work with some senor peripherals, everything is working fine, but sometimes, when we do testing...
Hi:
chip:nRF51822
code:ble keyboard
How to send the VIRTUAL_CABLE_UNPLUG request by Bluetooth HID devices?
If Virtual Cable Unplug is received by a Bluetooth HID device...
hello，
the datasheet of nRF2460 “nRF2460_Product_Specification_v1.0” has a explanation “the MCLK signal on the ATX side is locked to the
reference （crystal）of the ARX...
Hi all
In the documentation for the function "sd_ble_evt_get" it is mentioned, that this function may be called directly in the ISR for the SD_EVT_IRQn or from the main...
Hi
I am trying to make the ANCS example run on my dev board but i would like to use my on makefile. what i would like to know is where in the memory mapping should we start...
