I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
Hi,
I try to modifie ble_multilink example et send more than one data,
here is my main code code :
static uint8_t test[4] = {0x41, 0x42, 0x43, 0x44};
static...
Hello,
SPIS is adding a 350uA from 80uA baseline running current. I would like some tips and advise on improving this. Thanks!!!
The baseline operation consists of:...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
Hi,
I am trying to send L2CAP connection reply by using this "sd_ble_l2cap_ch_conn_reply()",but i am unable to see the packet on wireshark. The incoming connection handle...
Hi I note here that it is recommended to apply solder mask to the ground layer beneath the nRF24L01+ exposed die so they don't connect:
devzone.nordicsemi.com/.../
But...
I'm finding a discrepancy with numbers between the nwp_008 whitepaper (quarterwave printed monopole antenna for 2.45ghz) and AppCad values.
I've assumed you can measure...
Hi.
Months ago I loaded the nfc_url_record example and it worked fine.
Later some time I updated the packages, and since then that particular example gives errors.
The...
Hi,
Anyone familiar/experiened in production-test gear for BLE?
Test sets, i.e. LitePoint, Anritsu, USRP, NI?
What's relevant to test, i.e. output power...
Figure 222 of the OP spec states "important: no components in bottom layer". Are you recommending that we keep the bottom side clear under/near the nRF52840? This feels a...
I met some problems in testing ECDH , the project is the example in E:\Source\NRF52832\nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
