Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I what to send button data , how to construct button data array :
uint8_t buffer[INPUT_REP_BUTTONS_LEN]; in function ble_hids_inp_rep_send() ?
In SDK mouse demo I can...
I want to add to lbs service battery service(bas) as well. One of the changes is in the advertising_init() function:
static void advertising_init(void)
{
uint32_t...
Hi,
We have a custom board, with accelerometer sensor, our ultimate aim is to collect the accelerometer data and transfer it to the master device (PC or smartphone) using...
Hi there,
Will any 4.1 features by making their way into the respective Soft Devices any time soon?
I would imagine 32-bit UUIDs would create some memory pressure on...
I am trying to use Eclipse+GCC for my projects. I found a similar issue as stated in the following post:
devzone.nordicsemi.com/.../nan-29-nrf51-sdk-no-project-files
...
I am having trouble getting up and running with the development kit (without the starter kit).
My setup is as follows:
The PCB antenna module is hooked up to the JTAG...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
When the Ant stack want to transmit a packet while the BLE stack is using the radio, an event called EVENT_CHANNEL _COLLISION will be returned, is that...
Hello,
when the device NRF8001 starts Advertise, it sends out only one packet and unexpectedly terminates with a fatal hardware error in "ll_ctrl.s0.c" line 572. This happens...
Hi,
I'm trying to install Master Control Panel v.3.5.0 on Win7 64bit but I get the "Master Control Panel Setup Wizard Ended Prematurely" message. I have .NET Framework...
It would be very convenient to increase the output power of nRF51422/822/922 with at least 3-6 dB in order to get enough range. I'm currently not using nRF51422 for ANT, only...
with 1.16.0.3031 I cannot recover but I still can recover in Linux using a tweaked Makefile.posix
I don't remember this problem with previous version. Hence it must be...
I have tried to configure the nRF24A2 chipset in the asynchronous transmission mode by setting the bits in the extended field assignment. Unfortunately for some reason, it...
Hi,
I want to use 51822 to communication with 24l01,the 24l01 module is transmit temperature data, the 51822 is used to read the data from the 24l01.I set the parameters...
Hi,
I recently started on the nRF51822 Evaluation Kit and got the blinky code/example running. I then tried getting the Heart Rate application going but noticed when I...
