I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I am working on ota ble_secure project. I have created a zip file which is the last step and copied this file to my smart phone so that I can upload it using nrf toolbox...
Apparently you need to set the CCCD handle of your target characteristic to enable notification. Problem is, how do you do that? I now know at least 2 ways to do that, one...
Hello!
I am using application that support ANT+ and BLE, so i am using s332 softdevice.
now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v12.2.0...
I am using the nrf52 development board, when I try to connect to one of its pins a signal from a sensor that generates an interrupt signal every 1ms the programs stops or...
Hi,
I have relay board which is attached to the SoC module nRF9E5 and also microchip serial SPI EEPROM 25AA320 is also attached.
I have the EEPROM programmer and I am...
Is it possible to connect more than one device over bluetooth to single router (Raspberry Pi 3 under archlinux)?
I connect using commands:
echo "connect 00:4D:25:16:1A...
Hi Nordic team!
In my company project, we are using the NRF52, and, apart of other peripherics, we need to use the NFC.
As the NFC isn't always exchanging data with the...
Hi all, As I known sdk13 have bluetooth 5 features that means we can send more than 31bytes in advertising data (8xdata) right? I'm using nRF52832 and softdevice s132 v5.0...
hi,
i'm not able to have the nRF24LE1 go to sleep. I'm using the example at the link below, to which I've added code for UART and ADC usage. Is there a way to end the...
hi
i am working eclipse for setting up projects for nrf52832. When i build the blinky example there is no error but the headers nrf_delay.h are not include and the LED_LIST...
Hi,
I want to write flash using received data in BLE interrupt handler(on_ble_evt()).
When i received some data from BLE, i try to write it to flash and wait until done...
Hi
I'm trying to use the nRF52840 USB Serial UART device (aka USB CDC ACM) however I can't find a Windows driver for this device
The VID is 0x1915 and the PID is 0x520F...
I need to copy a string, but i don't know how to define nor how to copy.
This is the string that i have to copy dev_name.p_data.
I use soft device S130 in NRF51
