According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
Hi,
What is the maximum voltage a level than can be given as an input on a pin on nrf51-dk? I've measured VDD at 2.91V. Is it from VDD-0.3 to VDD? If yes, is there a way...
Now I am trying DFU via BLE, some times I can do it successfully and I can do it as long as i want to, but the other time it shows "Error(0x85) GATT error" message and whatever...
I'm testing the DFU as described in this link developer.nordicsemi.com/.../a00086.html
after reseting in DFU mode, when I start the device discovery, I only get empty packets...
Hello
Quick question. With the nRF51, When in System On mode, should I manually disable peripherals to minimize power even if I'm not using the peripheral in question?...
Can I use RTC1, whitch is used by app_timer for button debounce, ble_conn_params and so on, to realize the time function (hours, minutes, seconds,day, week,month, yea)? And...
Hi, I'm not completely sure if this is a bug but I've been struggling with this for two days so I don't think this is related to my own application code.
The situation...
I tripped over what appears to be a change in the RADIO between nRF51 and nRF52.
For the particular case of issuing a STOP task when the radio is in Rx mode, there is no...
