Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hi
I am quite well familiar with DECT-NR+ and the Nordic Boards, as well as nrf91xx, we use a nrf9151.
Also some kind of involved at this opener initiative, but I cannot...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
I hope, as a non-EE, I'm clear with my challenge ...
My student EE designed a small PCB with a couple of sensors (CO2, temp/humid, microphone) with an nRF52811. The boards...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
how to configure uart communication between nrf54l15 and tc334 via uart and i need to control my nora b2 evk leds based on mesage from tc33 using tlv can anyone give me idea...
Dear Nordic team,
Please tell me the theoretical power consumption of the nRF54L15 when using CH—both for the initiator and the reflector.
Best Regards,
Riki Yosh...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
I installed NRF Connect, the BLE plugin, and successfully flashed the dongle firmware. IIn NRF connect, the BLE plugin scan button is disabled. 'Quick Start' was unable to...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
nRF91 repeatedly transitions to `+CEREG: 4` approximately every five minutes while roaming on Vodafone Germany
## setup
nrf9151 modem FW: mfw_nrf91x1_2.0.4
current SDK...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
While building the program I get this error message: "DT_N_NODELABEL_cpucell_cpuapp_ipc_shm_trace_REG_IDX_0_VAL_ADDRESSU" As far as I can tell, this error message is releated...
