I just developed a BLE peripheral using an nRF54L05 MCU powered by an nPM2100 PMIC. When I flashed it with a simple blink LED firmware using a JLink via SWD, everything worked...
I am using OpenThread Secure CoAP with DTLS/PSK on an nRF54L15 DK.
Environment:
nRF Connect SDK 3.4.0
Zephyr 4.4.0
nRF54L15 DK
OpenThread Secure CoAP API ( otCoapSecure...
I'm trying to use the Hello nRF Cloud firmware, but when opening the website I get this error:
Fingerprint: <fingerprint>
Connection failed.
The fingerprint you have...
Dear Nordic support,
We are bringing up LE Secure Connections as a GAP Central on nRF52832 with SoftDevice S332 (BLE + ANT, nRF5 SDK 14, BLE API v5). The nRF runs the serialization...
Can anyone verify what two pins are used for NFC on a FANSTEL - BM20C module? I've been in contact with Fanstel for over a week, but they haven't given me a definitive answer...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
Hi,
The fstorage library is not available for NCS. Instead, the OS Service "Settings" should be used. (see the last answer of this thread )
In fstorage, it is possible...
I am working on a prototype using the nRF Connect SDK v2.1.0 on the nRF52 Thingy platform.
For my prototype, I need to store normal log output on the internal flash of the...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hi all,
I use GPIOTE and DPPI to read SPI data from IMU sensor. After IMU send out "Data Ready" signal, GPIOTE will be triggered and DPPI start to read using SPIM2.
And...
Hello ,
I am working on a project an nRF52840 + quectel BG96 modem. I am porting the freeRTOS cellular interface library for the Nordic platform and mainly the FreeRTOS...
Dear all,
I am developing a device that base on nrf52833, nrf connect sdk ver 2.0.0
The device run bluetooth mesh. And becase it was powered by battery, so it must go...
Hi there,
There are some problems when setting nrf52840 GPIO interrupt. When I use gpio_pin_interrupt_configure_dt api to configure 11 gpio pins then download to my customer...
Hi
I am testing <InstallFolder>\examples\peripheral\usbd_cdc_acm project, when I use serial tool of pc to open port, it can send or receive data.
but if I don't want to...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
Hi, I am looking to use mcuboot to manage 2 separate images. The idea is that under certain conditions, image 1 would jump to image 2.
To test the idea, I am using the zephyr...
