Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Since I encountered some issues, I would like to confirm the differences between these two files once again.
Apart from debug messages, can prj.conf be used for the final...
Hello, I just had a look at the Thingy:91 X with the nRF9151 and nRF5340 SoC's including nRF7002 Wifi support.
My understanding is that the nRF5340 is the main MCU running...
Hello,
We are in the feasibility stage of a product that requires integration of both the Apple "Find My" and Google "Find My Device" technologies.
Based on my research...
hi
We are developing with Segger embedded studio.
.
If you copy and move the SW development project folder to another PC, the following error occurs.
(Only occurs...
Hi,
Very beginner to this so bear with me.
we are testing an asset tracker which uses edrx. The asset tracker can receive a wake-up sms command.
However the network...
Hi,
I have ported my already working nRF52840 SPI slave code to a nRF5340, but it doesnt seem to receive any data. I have verified the CS, SCK and MOSI signals, but no MISO...
Hi,
I was wondering, what is the professional, assembly line ready procedure to program the IMEI on an nrf9161?
So far, I've only found rajeev's post in this discussion...
Hello,
I am using a Raytac MDBT50Q (nRF52840) on a custom board , and I am trying to blink an LED, but it is not working.
"I need urgent help as this is blocking my...
We can get BLE address in adv report: How to get mac address of nearby ble devices? - Nordic Q&A - Nordic DevZone - Nordic DevZone
At that moment, peripheral not connected...
I have download this .zip from the Nordic site. I am a beginning coder and I am using AI to help assist me on my project and learning C code. I seem to unzip the file correctly...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
