I am using OpenThread Secure CoAP with DTLS/PSK on an nRF54L15 DK.
Environment:
nRF Connect SDK 3.4.0
Zephyr 4.4.0
nRF54L15 DK
OpenThread Secure CoAP API ( otCoapSecure...
I'm trying to use the Hello nRF Cloud firmware, but when opening the website I get this error:
Fingerprint: <fingerprint>
Connection failed.
The fingerprint you have...
Dear Nordic support,
We are bringing up LE Secure Connections as a GAP Central on nRF52832 with SoftDevice S332 (BLE + ANT, nRF5 SDK 14, BLE API v5). The nRF runs the serialization...
Can anyone verify what two pins are used for NFC on a FANSTEL - BM20C module? I've been in contact with Fanstel for over a week, but they haven't given me a definitive answer...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
Hi,
I have 2 nrf52840 DK boards advertising on coded PHY mode. Once connected the connection is updated (using sd_ble_gap_phy_update()) to use 2M mode. No problem in doing...
Hello! I add an attribute array (0x48) for the user cluster. Having problems using the "array" attribute:
1. If you select the data type of 16 or 32 bits, then an alignment...
I have some questions on using the nrfutil dfu ble with the buttonless example.
Should both devices (central and peripheral) be already bonded before starting the DFU process...
Hello,
Using NCS 1.6.1, I would like to use the radio from within a timeslot as suggested in the documentation . However, the MPSL/timeslot sample is quite sparce and only...
Hi,
It's been a few months since I've been developing a new project using the nrf52832. One of the main features is naturally the OTA DFU. During the last months I was able...
Hello,
I noticed that slighly incresed amount of printk output in the B0 bootloader leads to the corrupted debug output.
1st case - I added two printk lines starting with...
Hi,
I was in a strange situation using nrf52832QFAA.
I'm using nRF52832 and nRF52840 evaluation board.
When i download code using Programmer(nRF Connect), the memory...
