Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
ncs tag 1.6.1
Ubuntu 20.04
Hi
I am evaluating the Nordic nRF52840 using the Connect SDK. The nRF5 SDK has an example, ble_app_multiperipheral, showcasing a single peripheral...
Hi Everyone, I'm trying to know and make a handler for the ble advertasing, and I've front with the doubt if there's a way to know when the program will change of advertising...
We have designed an electronics product - a PC peripheral and are looking to release it to market. It’s basically a ATSAMD21 microprocessor connected to a battery, which charges...
My requirement is to send 16kHz 1channel voice data stream to pc .
I use 16khz (2 channel and 1 channel) wav and 1 48khz (2 channel) wav as input (converted to .c file)...
Hi Nordic team,
I was working on nRF DFU (secure_bootloader_ble_s140_pca10056) .I just want to advertise my device mac id to Phones app while in OTA mode to specify devices...
We want to use the iperf3 tool to measure packet loss while sending packets between two nRF52840 DKs. But we can't seem to find any instructions. We are using a variant of...
Hello,
I use zb_cli_wrapper.py and the Zigbee Cli Agent Router example.
I try to discover attributes from a GreenPower endpoint (242), the commande is :
communicator...
Hi,all~
The program runs on nRF52833.The SDK version is NRF5_SDK_17.0.2_D674DDE. At the beginning, MCU sends data to nRF52833 through serial port, and the data can be received...
Hello,
It looks like a possible policy issue - but I was wondering if anyone here has successfully provisioned IoT in this Amazon AWS Region/Endpoint: iot.ap-northeast-1...
I am trying to deploy an trained Impulse module into nRF52840, but not sure about how to do it.
In the edge impulse documentation, they mention we can link the impulse from...
We've been chasing a seemingly randomly appearing bug, where a call to the Zephyr MQTT library seems to sometimes block indefinitely. More specifically the hanging function...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When receiving advertisements, "nrf_ble_scan_filter_set" is used to filter the device...
Hi ,
There is an error when to debug the nRF52840 target board by the PCA10028 board(as error information).
(pls note, There is running okay when to debug the nRF52840...
