Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
I'm trying to sniff BLE communicate data between the devices with nRF51822.
I have connected one device to the selected it with the interface toolbar. But I can't sniff...
Hello, I am using the ISP1507-AX and want to compile the BLE UART Mode Example "ble_app_uart_pca10040_s132" with SEGGER Embedded Studio in order to generate a hex file like...
Hi,
We have been working with nRF52832 and using BLE Mesh in our product. The product is an Access control reader which scans for nearby smartphones over BLE and sends...
Module model: nrf52832
SDK: 15.2
Hi,
I am trying to add custom characteristics to a custom service.
There are two ways that I am aware of:
a. sd_ble_gatts_characteristic_add...
I have a firmware version present SDK 13.1 and S132 SoftDevice v4.0.5 I am trying to do a DFU (just SD+BL first) which now has SDK 16.0 and S113 SoftDevice v7.0.1 But my package...
Hello, I have a issue about flash_manager module.
When I load a program on processor (that has been previously erased) there is a problem with initialization (flash_manager_add...
I'm trying to get a temperature reading from the on-chip temperature sensor on the NRF52832 - I know it is not a very accurate sensor but I still want to use it. I found a...
With IAR (EWARM) 8.50.9 the UART project in the SDK compiles fine.
After upgrading to IAR (EWARM) 9.10.1 or 9.10.2 I get compiler error:
Error[Go029]: Variable "sec_mode...
Hi!
I'm trying to use a precompiled library of TVOC sensor ZMOD4410 in a project based on the azure_iot_hub from Nordic, running it over a nrf9160 board.
This library...
When I follow this tutorial and build the secure BLE bootloader example, I got this error:
cannot find ../../../../../external/nrf_oberon/lib/cortex-m4/soft-float/liboberon_3...
Hello,
I've been working on a big software project on the nrf52 DK with Segger Embedded Studio and added a lot of libraries and drivers. The issue I ran into is that if...
I am attempting to update firmware on hardware already in the field. The firmware in the field is based of sdk v11 and has the legacy bootloader for OTA DFU. After some digging...
Hello Nordic,
Due to recent shortages we have switched from a BLE module with external LF oscillator (uBlox Nina-B3) to a module without external LF (Laird BL654). We have...
Hello,
I'm currently starting to develop with the Nordic nRF5340dk and trying to build a mesh network but i'm having some trouble on the examples to understand and buld...
