Hello
I need some advice on FOTA via BLE on the nRF54LM20B. I managed to get FOTA working to upload an updated image via BLE, but after a reboot, the new image doesn't load...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
When trying to add the device to the Nordic Cloud Device Management interface, I get the following error.
"There was an error adding your device: No device found for this...
Hi,
I am using the heart rate sample.
I have connected ground to ground, 3.3v to vdd, SDA to pin 26 and SCL to pin 27. I have 4.7k pullup resistors on SDA and SCL. When...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
We use the NRF Mesh Android Library (and are developing with iOS version as well). An issue that we are running into on a small number of devices is that the library things...
I am looking for an example where I can enable UARTE0 and UARTE1 on the nRF52833 DK. I am using nRF5_SDK_17.0.2 with Keil uVision V5. I am successful with the loopback example...
Hi,
I'm new to building circuits with Nordic devices and am unsure about how to connect the MC3672 accelerometer: https://mcubemems.com/wp-content/uploads/2020/03/EV3672AB...
Hello,
We have been working on Nordic nRF52-DK board.
Board can be reachable by Bluetooth in the first 10 minutes of power supply. However after 10 minutes, we can...
Hi everyone ! I am working at a project. I dont't know which mcu was used this project but it was written for pca10040 and used s132. Many values are write to flash memory...
I merged in some of my code to the examples/thread/dfu/client in the v4.1.0 SDK for Thread and Zigbee. After getting OTA DFU working, I moved onto some commissioning related...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
I am working on a BLE Product which connects to a remote device when detected within a certain proximity (based on the RSSI values). After switching on the scanning, I receive...
Hii Guys,
I am trying to run example code ble_app_uart on my nrf52810 sdk module . But when I try to run the code in debug mode I get an error of Vector Catch Error ....
Hi, I am working on nRF52840. I want to add GSM MQTT protocol. Is there nordic soc available for this? Which we can later communicate with nRF52840 peripheral device also...
