Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hello,
I'm implementing libuarte with ble_app_multilink. But receiver side receive gibberish like below.
It looks like RTT message is printed to serial port. But I...
I am using nrf9160 for a monitoring project using NB-IoT network. The problem I am having is when I go to an area where there is no NB-IoT network, the device crashes often...
Hi,
We've a custom board which has NRF52832 and Maxime. They are connected over UART. ( I'm using ble_app_uart)
What I want is transfer binary data between Phone and...
Hi, i am trying to understand the SDK 17 by building my own libraries such as interrupts, ADC, IIC or so on. I was doing well untill i come across with "LOG". When i look...
Newly purchased nRF51 DK connected via USB cable to a computer. Attempted to program firmware via BLE sniffer and an error occurred (image attached). Connected nRF51 DK does...
I am porting our firmware from SDK v15.3.0 to 16.0.0. I believe I have most of the changes in place as I am able to build the boot loader and get it to execute without any...
Hi
I'm trying to use Crypto but can't get started because micro-ecc isn't installed
The install instructions say:
Enter the subdirectory for the SoC and the toolchain...
I have been trying to bring up a secure boot loader for our product based on the nRF52832 SoC.
I have reviewed three SDK versions (17.0.2, 16.0.0, 15.3.0) and observe the...
Hi,
I know that the QSPI peripheral of nRF5340 allows to augment memory by interfacing an external SPI Flash memory. In addition to the internal memory, does DFU by FOTA...
I use nrf52840 dongle on windows 10 to connect to ble devices, I can connect and send msg to the ble device ,but I tried "att_res, data = self.adapter.read_req(new_conn,BLEUUID...
Hello Everyone,
I'm looking for an MCU that could be used as a master for SPI communication to supply the necessary signals (CS+, SCLK+, MOSI+) to a slave device (amplifier...
Hello,
I have migrated my codebase from v1.3.0 to v1.4.0 of the nRF SDK and have a strange issue now where the serial port is spitting out sleep debugging information in...
Hi,
The nrf52832 product spec shows all the clocks provided by HFCLK and LFCLK. But where can I find which peripheral is using which peripheral clock specifically?
For...
Hi,
I need to read some BLE characteristics presented by a commercial device nRF52-based, using my nRF52-DK, based on the nRF52832 and PCA10040. I don't have the firmware...
Hello experts,
I would like to get my mind clear on this.
I am using NRF52833 for our custom board we are using Zephyr RTOS (NCS v1.4.99) and IDE is segger embedded...
