I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello.I want to use the nRF SDK for Mesh,but I don't kown how to use it.I need help.Does the official website provide sample programs? I opened the SDK file, but I don't know...
Hi,
I am using nrf52832 for the beaconing device. The device is working fine, sleep current, wakeup current is normal, transmit cycle is also working fine but the device...
Hello,
I have been working with BLE on the nRF52840 with softdevice 140 and the latest in terms of SDK.
The problem I have run into is with reading the value that has...
Hi,
If anyone having driver for the ELW0901AA1 FUTUBA OLED please help me to send the same.
I am working on nrf52833 custom board and SDK version that I am using 17...
Hi,
I would like to know the current consumption in advertising when I set PRF = 0 dBm and I use LDO.
I read nRF52832_PS_v1.4.pdf.
23.15.2 of nRF52832_PS_v1.4.pdf...
Hello
I need to do SD Card with nRF52840-DK. I have referred (zephyr/example/subsys/fatfs) sample program, based on that I have made one new project and also made overlay...
Hello sir,
I was referred this link ( https://github.com/zephyrproject-rtos/zephyr/issues/29921 ) to do USB DFU on nRF52840-DK, but I am facing an issue in this code is...
Hi! I looked at the specifications, and it doesn't seem like this is listed as not possible, but it strikes me like it should not be possible, so I wanted to make sure. Looking...
Dear Nordic,
I am using the pre-build option to build always rebuild a file. This file is used to setup the date and time stamp of the build. I have done something similarly...
Good day,
I would like to start this thread by saying that I have been developing an application using the nRF52832 chip for several months, so far it has been a very difficult...
Hi,
I am beginner with nrf9160 and its SDK. I want to send data from nrf9160 to an external flash memory. To test it I wanted to start simply by sending hello_world(sample...
Hi,
I'm usgn Nrf528332, Softdevice s132_nrf52_6.1.0_softdevice
I Use secure_bootloader BLE secure_bootloader\pca10040_ble with the public key, and matched privet Ket...
I have installed the latest SDK 1.3.0 using the Toolchain Manager.
I would now like to open nRF Connect SDK Projekt and get the follwoing error:
I have added the CXX...
Hello
I have several questions regarding the UUID (Bluetooth):
If I create an application using your nus bluetooth service (ble_nus.c), should I change the NUS_BASE_UUID...
