This is long and AI generated. Sorry about that, but it is comprehensive.
I'm seeing a very specific, repeatable failure uploading a file via mcumgr's fs_mgmt over BLE,...
Hello,
We run our Bluetooth Mesh product firmware in BabbleSim, on a simulated nRF52840 (nrf_hw_models, native simulator). We are on nRF Connect SDK v2.9.0. We would like...
An external MCU occasionally sends data to the nRF54L05 over I2C. Between transfers, the nRF54L05 should sleep and wake when addressed, without a separate wake pin.
What...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Thanks in advanced. I'm immigrating projects into NCS bare metal v2.0.1. Sample Bluetooth ble_nus only advertises for 3 minutes, then device can't be scanned again. I check...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
Hello, Second time in here, thank you so much for all the support so far!
I'm developing a Beacon BLE, I wanna be able to send data over Advertising or Scan response. So...
I am trying to implement ble_app_interactive on nrf52840 as my application will require 2 uarts. I have started from the example application for the nrf58832 and created a...
in nRF52840, current consumption can be decreased by executing code from RAM instead of from flash. How is it possible to execute code from RAM? how to executing code from...
Hi, I have one nRF52840 DK and 2 nRF52840 dongles, i used the latest SDK17.0, programmed nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_blinky\hex\ble_app_blinky_pca10059_s140...
MacOs on a macbook pro with LMP 9 (BLE 5.0 support) and a new DK2 board, SDK 16; no example built
and downloaded (SES) is discovered by the mac (same with an IPAD 2 pro...
Hi,
I need to read a digital signal with varying pulse widths (Min ~120µs) over ~30ms. Currently (nRF52832) I'm doing this using a timer interrupting every ~15µs and reading...
Hi Nordic Team：
I use this example " Thread Google Cloud Platform CoAP Example ",
I setting up the cloud is finish, but I Thread device of google_iot_coap not join the...
Hi everyone,
I'm new with nordic chips and for our project we use a custom board based on the famous nRF52840 mcu. I read a lot about SDK17 in the infocenter to find how...
Hi
The latest OpenThread/Zigbee SDK has no examples for openthread with the PCA10059 (No MBR, executing directly from 0x0 @ flash start).
Ive tried now multiple times...
nRF52840, SDK 16.0.0, SD132v7.0.1
What's the correct way to tell whether HFXO or HFINT is clocking the HFCLK controller? I'm able to start and stop the HFCLK controller...
Hi, i am using the nRF52dk would and im using the pwm driver example and im trying to understand the way the seq_values void works when it comes to phase or sequence would...
Hello, I uses the NORDIC project saadc_low_power. A counter was built into this so that only a defined number of samples are carried out. Measuring current on an nRF5 DK while...
Hi,
I have a custom PCB using the Johanson 2450AT18A100E chip antenna. For some reason, I'm getting extremely subpar RF performance and so I'm taking a second look at...
Hi I have a nrf5340 pdk version 0.8.0 (PCA10095) When I plug it into my Win 10 (latest version 2004) device manager tells me it sees 3 comports
When loading the 'Peripheral...
I want to change between LTE-M and NB-IOT, however lte_lc_system_mode_set(); is not actually changing the mode.
I am doing something like this
I can't rely on PSM/eDRX...
