Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
I hdd developed a ble product based on nRF52810 ( SDK_15.3.0_59ac345 s112 ). I had set the connect paramter like this:
MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_1_25_MS...
Hi,
Do you have a better example than the one on nRF Cloud that can show me how to transform a HTTP GET /message from my thingy. Right now, the messages are nested and it...
While I know the 9160 does not support voice calls, I would like to know if the 9160 will accept mobile terminated (MT) data calls. If so, how is that represented in the firmware...
First of all , p lease forgive me for m y bad English if it annoys you .
I do have an interest in nRF52840 development kit, because I am trying to find a development kit...
After updating from THREAD SDK 2.0 to SDK 3.1 I am getting NRF_ERROR_NO_MEM in nrf_sdh.c.
The project is based from the multiprotocol BLE thread dynamic example.
The code...
I'm creating a ble central device that receives instructions via UART on which device to connect to and which UUID to write to.
I'm able to connect to a peripheral device...
Hi,
I am working with NRF52840 and want to encrypt my saved data with AES using CC310 cryptocell.
I am working with nrf_crypto_aes frontend to do AES.
I want to know...
Hello,
I'm trying to build and run 'secure_bootloader/pca10040_ble_debug/armgcc/' example and it seams that it stops with some hard fault:
Remote debugging using localhost...
Hi,
I tried to evaluate the light switch demo using the boards that I have to my disposal.
These are 1 nrf52-DK and 2 nrf52840 Dongles.
I wanted to use one dongle...
in application design , this pin is not connected to VDD , but application board works well ,
application's power range is 2.2V - 3.3V (AAA batteries), max current consumption...
I'm attempting to troubleshoot why my HM18 doesn't connect to the ESP32 over BLE. I'm now deep in the rabbit hole that is BLE sniffing so now I'm trying to determine if the...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
